Iron On Patches: Choosing the Type of Adhesive for DIY Iron On Patches

If you are the type of person who looks for quick and creative alternatives to sewing those hole-y or ratty fabric clothes and bags up, you are most likely already familiar with iron on patches and how it works: You buy one to your liking which is big enough to cover the hole of your old jeans, you peel off the protective cover on the adhesive at the back, and press it down with your flat iron for a few minutes till it sticks on the fabric and voila, in place of that nasty hole is a cute patch accessorizing your old jeans. But did you know that you can make your own iron on patches? All you’ll be needing are the following materials: embroidered patterns from old or outdated clothes, a pair of scissors, flat iron, a base fabric to decorate or stick your patches on, and most importantly, your fabric adhesive.

Making your own iron on patch is really not all that complicated – especially when you figure out that the durability and stickiness of iron on patches rely on the type of washable and heat-resistant adhesives used on its back’s surface for it to permanently stick onto the fabric. There are four types of adhesives that craftsmen and designers commonly use to stick decorative patches onto bags and clothing;


These are the MOST advisable and appropriate glue for sticking on embroidered patches. It is basically mess-free and easy to bring along in strips inside your sewing kit when traveling. There is no chance for leaks and drips when not in use as the fabric glue or adhesive come in sheets with protective peel-off layers.



This is the most commonly used and often in-stock glue available in hobby and crafting stores. Fabric glue is often in thick liquid form sold in small, plastic-bottles with an applicator, or sometimes in easy-squeeze aluminum tubes much like tooth paste and permanent bonding glue.


“Usually”, but NOT always, non-toxic and safe for kids to use in their little crafting activities. If you are on a tight budget or don’t have the time to make or buy iron on patches but are in DIRE need of a quick fix to “accessorize” or “temporarily” cover the hole in that tote bag or t-shirt, this crafting water-base glue is the way to go. Note that this type of glue has a tendency to seep easily onto fabrics so be sure to only apply in little amounts – unless you’re not worried about ruining your work.


These are definitely NOT fabric-friendly. These are basic, extra- strong bonding glue used for wood, plastic and glass materials. They may be clear or colorless solvents, but these are best used on solid, non-porous materials only. When used on fabric, this type of glue may leak through it and permanently stiffen the area of the fabric it is applied on. From the word “permanent”, this type of glue is NON-WASHABLE and should be used with caution. Only use this type of glue to stick your patches onto your fabric IF you really have no other choice and are in the ULTIMATE need of a quick fix.

Being aware of the different types of glue to stick on your Do-It-Yourself iron on patches can help widen your options in choosing the type of raw materials best suitable for your fabric and crafting needs. Without a doubt, these bits of crafty knowledge will help you determine the washing durability of the patches and save you money and effort in the long-run.

Author Bio:
You know that you can make your own Iron on patches You are most likely  familiar with iron on patches and how it works.

8 Things to Consider Before Investing in a Portable Storage Container

Whether you intend to purchase or rent a portable storage container, this is a pretty large investment. As such, you want to be sure that you are spending your money on the right one.

portable storage container

To do so, there are some factors that you have to consider first before you agree with a company to rent out or purchase one of their containers. To help you make that decision, here are the top 8 things that you have to look into when choosing between the storage containers available.


Most storage containers have branded locking systems that can help ensure the security of the items you store in your container.Most containers also include security features that protect your items, not only from possible theft, but also from other factors that may damage your valuables, such as fire and storms. Make sure that you check for these security features before purchasing or renting a portable storage container.


Portable storage containers commonly come in three sizes—10-foot, 20-foot, and 40-foot containers—to give you options on what size is more suitable for the type of items you plan to store in them.


The metal portable storage containers that you choose should be rust-resistant. It’s almost always a given that these containers are already rust-resistant, but it’s best to be sure and ask with the company before investing in one, especially if you intend to use the container for some time or if the weather conditions are unpredictable in the area where they will be stored.


If you intend to use the portable storage containers as mobile class rooms or offices, you should choose customizable containers. Not all companies allow for their containers to be customized, so if you plan to convert a container to a room or office, make sure you inquire with the company first if this is possible.


People often pay little attention to the doors of portable storage containers when making a decision on what container to invest in. There are some containers that prove to be hard to use because the doors aren’t too easy to open. It’s important to choose a container with some sort of special fitting or patented technology that allows you to open the door easily, especially if you know you’ll be coming in and out of it often.


Before you invest in a portable storage container, you should already have planned on where to store it so that this won’t be a problem once the container is delivered to you. If there is no space for the container in your home or workplace, most companies will allow you to keep them in their storage areas.

Rental Agreement

If you plan to rent a container and not purchase it, make sure that you are provided with a copy of the rental agreement and that you read through it before signing anything. Don’t hesitate to clarify anything that seems confusing for you, and make sure that the agreement allows you to return the container immediately after use so you won’t be charged for over-booking.

Overall Condition

Before you rent a portable storage container, check its overall condition. Make sure that you document any fault that you see—dents, rust spots, faulty features, or damages—because you might be held responsible for them. See to it that these faults are written onto the agreement so you won’t be charged for them afterwards.

Use this as a checklist the next time you visit a storage container company so that you can be sure that the container you choose is the one most suited for your needs.

Do-It-Yourself PCB Fabrication

It is a wonderful opportunity to create a piece of technology that functions properly, the way you really want it to be. Because of this, many college students opt to study in Universities that specialized in degree programs such as Electronics and Electronics and Communication. However, if you want to practice electronics at home, you can do so. This way, you can take your creativity, resourcefulness, and other skills to the next level by creating or recreating electronic projects that you are interested in.

This article lets you in on one of the most cost efficient ways to do your own PCB fabrication.

Planning your DIY PCB fabrication

Before you go out and buy the material that you think you need, you must first plan ahead. This way, you will purchase those that you need only and nothing more. It is a way to produce a cost efficient but definitely effective electronic device.

First off, think of what device you want to create or recreate. For example, you want to recreate a radio transistor. Carefully think out what components you will need in order to produce the required type of connection on the PCB. As you think about the device and the requirements for it to work, try to create a picture if it in your mind.

PcbfabricationNext is to draw your schematic diagram. This is when your mental image of the device becomes necessary. Did you picture your device to be small or big? If you prefer a handier transistor radio, then you may need to sketch a smaller diagram. But you need to keep in mind that the smaller your schematic diagram is, the more elaborate and meticulous you should be in making the PCB.

While drawing the diagram, you should be aware of how many resistors, capacitors, diodes, and transistors are needed. Make way for an on and off switch. You may also want to add embellishments like led lights to indicate whether the device is on or not. Consider all of these things before you purchase anything.

The PCB fabrication procedure

The next step is to determine what etching method is the best for you. You can choose among four methods. This includes the acid etching method, UV etching method, mechanical or routing etching method, and the laser etching method. For homemade PCB, the most advisable is the Acid etching method.

In this method, materials are very much available in most hardware stores. However, this is also the slowest and the messiest. You can use Ferric Chloride or Ammonium Persulphate. These two chemicals attack metals such as copper (the usual conductor surface of a PCB).

After purchasing a board, the acid of your choice, electronic components, and a permanent marker (for masking the needed portions of the copper surface), you are now ready to conduct your PCB fabrication.

Draw the layout of the schematic diagram on the copper surface of the PCB using the permanent marker. This way, the needed part will not be corroded by acid. Once you have drawn the layout, set it aside to dry. Meanwhile, mix the Ferric Chloride granules with warm water. The more diluted the solution is, the less effective it will be. Submerge the PCB you have prepare in the solution.

After a while, the unneeded portions of the copper surface will be removed. You can now drill holes on appropriate parts of your PCB. Drill holes on ends of copper surfaces, so that you can mount the necessary components.

Then, mount the components and solder it using a soldering iron and lead. Let it cool down for a while, and then conduct a test experiment. If it works, then you have successfully done your DIY PCB fabrication!

High quality Pcb fabrication and assembly. We ship PCB Prototypes the Same Day! INSTANT on-line quote and ordering. From prototype to production of single, double, and multilayer PC Boards.